Specifications

Maximum Operating Pressure:

• 60,000 psi (4,140 bars)

High-Pressure Flow Rate:

• .80 gpm (3.03 lpm)

Intensifier Cycle Rate:

• 25 cycles/min. at max. flow rate

Electrical System:

• Main Motor: 40 hp / 30 kW (TEFC)
  • 208v / 3 ph. / 60 Hz
  • 240v / 3 ph. / 60 Hz
  • 480v / 3 ph. / 60 Hz
  • 400v / 3 ph. / 50 Hz
• Air/Oil Heat Exchanger Motor: 1/4 hp / 0.18 kW
  • 120 VAC / 1 ph. / 60-50 Hz
  • 208 VAC / 1 ph. / 60-50 Hz
  • 240 VAC / 1 ph. / 60-50 Hz
• Motor Speeds:
  • 1800 rpm @ 60 Hz
  • 1500 rpm @ 50 Hz
• Controls:
  • 120 VAC / 24 VDC
• Safety Shutdown Circuits:
  • High Oil Temperature
  • Low Oil Level
  • Low Water Pressure
  • Intensifier Over-Speed
  • Intensifier Stall

Hydraulic System:

• 2.75 cu. in. (45 cu. cm) Axial Piston Pump
• Max. Operating Pressure: 3,000 psi (207 bars)
• Cooling Water Flow Rate: 2 gpm (7.56 lpm)

Low-Pressure Cutting Water System:

• Optimum Inlet Pressure: 65 psi (4.50 bars)
• Booster Pump Setting: 175 psi (12.0 bars)

Orifice Capacity at 55,000 psi (3,800 bars):

• Quantity / Orifice Diameter
  • 1 – 0.012 in. (0.30 mm)
  • 1 – 0.010 in. (0.25 mm)
  • 2 – 0.007 in. (0.17 mm)
  • 4 – 0.005 in. (0.12 mm)

Physical Dimensions:

• Height: 36 inches (0.92 meters)
• Width: 34 inches (0.86 meters)
• Length: 59 inches (1.50 meters) without control panel
• Length: 70 inches (1.78 meters) with control panel
• Weight: 1,850 pounds (840 kg)

Features and Advantages

Electrical System:

• Proven, heavy-duty industrial high-pressure intensifier with
  ceramic plungers.
• Slow intensifier speed –
  25 cycles/minute.
  This slow speed reduces both
  the number of pressure spikes
  in the system and the number
  of pressure reversals.
• One large (5” OD) accumulator
  ensures low pulsations in the
  high-pressure system.
• A pneumatic bleed-down
  assembly provides
  depressurization of the
  high-pressure system
  immediately upon shutdown.
• All high-pressure tubing and
  fittings are Autoclave.
• Highly reliable proximity switches
  control the sequencing of the
  intensifier.
• Oversized, low-load motor.
• Low hydraulic oil pressure –
  3,000 psi / 207 bars.
• A dial, main compensator
  allows for simple control
  of the cutting water pressure.
• The unit has a hydraulic oil
  cooling system with a full-flow
  oil heat exchanger.
• The oil reservoir has an access
  lid for easy maintenance.
• Brass fittings are used on the
  entire inlet water system to
  protect against corrosion.
• Complete set of spares, special
  tools, and comprehensive manuals
  are included with each unit.